{"version":"1.0","generated_at":"2026-05-21T01:20:43+00:00","canonical_url":"https://puffco.link/device-ts/peak-pro-3dxl/rwrw","device":{"id":"peak-pro-3dxl","name":"Peak Pro 3DXL"},"issue":{"id":"rwrw","title":"Red/white flashing before or during heat cycle (chamber connection error)","pageTitle":"Chamber Connection Error (Red/White)","summary_plain":"When starting, or during, a heat cycle the device begins flashing red/white/red/white and won’t heat up or stops heating unexpectedly.","summary_html":"When starting, or during, a heat cycle the device begins flashing red/white/red/white and won’t heat up or stops heating unexpectedly.","updated":"2026-02-13","tags":["Connection","Chamber","Red","White"],"escalation_plain":"If you're still getting the red/white connection error after trying all the troubleshooting steps it may be an issue with the chamber.\nIf the chamber has recently been replaced or is new, and you're still experiencing this issue, please use the button below to submit a warranty claim.","escalation_html":"If you're still getting the red/white connection error after trying all the troubleshooting steps it may be an issue with the chamber.
If the chamber has recently been replaced or is new, and you're still experiencing this issue, please use the button below to submit a warranty claim."},"steps":[{"index":0,"id":"rwrw-step-1","title":"Reseat the chamber","detail_plain":"Remove the chamber, then reattach it firmly.","detail_html":"Remove the chamber, then reattach it firmly.","duration":"1 min","caution_plain":"Do not force the chamber, as this could damage the chamber or base.","caution_html":"Do not force the chamber, as this could damage the chamber or base."},{"index":1,"id":"rwrw-step-2","title":"Swab the chamber and base connection","detail_plain":"Clean the pins of the Chamber, and base connection point with a cotton swab soaked in 91%+ isopropyl alcohol. Once you've cleaned both, reattach, and attempt to run a heat cycle again.","detail_html":"Clean the pins of the Chamber, and base connection point with a cotton swab soaked in 91%+ isopropyl alcohol. Once you've cleaned both, reattach, and attempt to run a heat cycle again.","duration":"2min","caution_plain":"","caution_html":""},{"index":2,"id":"rwrw-step-3","title":"Deep clean the chamber and baase","detail_plain":"Submerge the chamber in 90%+ isopropyl alcohol for ~30 minutes, then remove and let it air-dry completely. Swab the chamber connection area on the base, ensuring there's no oils left in the chamber as this could cause connection issues.","detail_html":"Submerge the chamber in 90%+ isopropyl alcohol for ~30 minutes, then remove and let it air-dry completely. Swab the chamber connection area on the base, ensuring there's no oils left in the chamber as this could cause connection issues.","duration":"~60 min","caution_plain":"Never use water to soak the chamber; fully dry before use.","caution_html":"Never use water to soak the chamber; fully dry before use."},{"index":3,"id":"rwrw-step-4","title":"Retry a heat cycle","detail_plain":"Once the chamber has dried, reattach, and try a heat cycle again.","detail_html":"Once the chamber has dried, reattach, and try a heat cycle again.","duration":"1 min","caution_plain":"","caution_html":""},{"index":4,"id":"rwrw-step-5","title":"Reset your Peak Pro","detail_plain":"If the issue persists please try resetting the device by holding down the button for 20 seconds.It will flash white once completed, after that attempt to run a heat cycle again.","detail_html":"If the issue persists please try resetting the device by holding down the button for 20 seconds.
It will flash white once completed, after that attempt to run a heat cycle again.
","duration":"","caution_plain":"","caution_html":""}]}