{"version":"1.0","generated_at":"2026-04-07T11:29:45+00:00","canonical_url":"https://puffco.link/device-ts/pivot/no-cmbr","device":{"id":"pivot","name":"Pivot"},"issue":{"id":"no-cmbr","title":"3 white flashes when trying to initiate a heat cycle","pageTitle":"No Chamber Connected (3x White Flashes)","summary_plain":"Attempting to run a heat cycle results in the device flashing white 3 times.","summary_html":"Attempting to run a heat cycle results in the device flashing white 3 times.","updated":"2026-03-31","tags":["Connection","Chamber"],"escalation_plain":"If you're still getting the 3 white flash connection error after trying all the troubleshooting steps it may be an issue with the chamber.\nIf the chamber has recently been replaced or is new, and you're still experiencing this issue, please use the button below to submit a warranty claim.","escalation_html":"If you're still getting the 3 white flash connection error after trying all the troubleshooting steps it may be an issue with the chamber.
If the chamber has recently been replaced or is new, and you're still experiencing this issue, please use the button below to submit a warranty claim."},"steps":[{"index":0,"id":"no-cmbr-step-1","title":"Reseat the chamber","detail_plain":"Remove the chamber, then reattach it firmly.","detail_html":"Remove the chamber, then reattach it firmly.","duration":"1 min","caution_plain":"Do not force the chamber; as this could damage the chamber or base.","caution_html":"Do not force the chamber; as this could damage the chamber or base."},{"index":1,"id":"no-cmbr-step-2","title":"Swab the chamber and base connection","detail_plain":"Clean the bottom of the Chamber, and the battery's connection point with a cotton swab soaked in 91%+ isopropyl alcohol. Once you've cleaned both, reattach, and attempt to run a heat cycle again.","detail_html":"Clean the bottom of the Chamber, and the battery's connection point with a cotton swab soaked in 91%+ isopropyl alcohol. Once you've cleaned both, reattach, and attempt to run a heat cycle again.","duration":"5–10 min","caution_plain":"","caution_html":""},{"index":2,"id":"no-cmbr-step-3","title":"Deep clean the chamber and baase","detail_plain":"Submerge the chamber in 90%+ isopropyl alcohol for ~30 minutes, then remove and let it air-dry completely. Swab the chamber connection area on the base, ensuring there's no oils left in the chamber as this could cause connection issues.","detail_html":"Submerge the chamber in 90%+ isopropyl alcohol for ~30 minutes, then remove and let it air-dry completely. Swab the chamber connection area on the base, ensuring there's no oils left in the chamber as this could cause connection issues.","duration":"1–2 hrs","caution_plain":"Never use water to soak the chamber; fully dry before use.","caution_html":"Never use water to soak the chamber; fully dry before use."},{"index":3,"id":"no-cmbr-step-4","title":"Retry a heat cycle","detail_plain":"Once the chamber has dried, reattach, and try a heat cycle again.","detail_html":"Once the chamber has dried, reattach, and try a heat cycle again.","duration":"1 min","caution_plain":"","caution_html":""},{"index":4,"id":"no-cmbr-step-5","title":"Reset your Pivot","detail_plain":"If the issue persists please try resetting the device. Start by removing the chamber, then press the button 6 times, once the light stops flashing orange reattach the chamber and attempt to run a heat cycle again.","detail_html":"If the issue persists please try resetting the device. Start by removing the chamber, then press the button 6 times, once the light stops flashing orange reattach the chamber and attempt to run a heat cycle again.","duration":"1 min","caution_plain":"Ensure the chamber is at room temperature before reattaching to the Pivot battery.","caution_html":"Ensure the chamber is at room temperature before reattaching to the Pivot battery."}]}